questions
2

TKA Axial Alignment

Author:
Topic updated on 07/10/15 6:24pm
Introduction
  • Important consideration
    • pre-op planning
    • component insertion
    • ligament balancing
    • prosthetic design selection
  • Normal anatomy
    • distal femur in 5-7 degrees of valgus
    • proximal tibia is 2-3 degrees of varus
  • Technical goals
    • restore mechanical alignment (mechanical alignment of 0°)
    • restore joint line ( allows proper function of preserved ligaments. e.g., pcl)
    • balanced ligaments (correct flexion and extension gaps)
    • maintain normal Q angle (ensures proper patellar femoral tacking)
  • Mechanical axis of Limb 
    • axis from center of femoral head to center of ankle
Preoperative Evaluation
  • Radiographs
    • standing AP and lateral of knee
      • to evaluate for
        • joint space narrowing
        • collateral ligament insufficiency (look for lateral gapping)
        • subluxation of femur on tibia
        • bone defects
    • standing full-length radiographs (AP and Lateral) 
      • are indicated to determine an accurate valgus cut angle when the patient has
        • femoral or tibial deformity
        • very tall or short stature
    • extension and flexion laterals
    • sunrise view
Femoral Alignment
  • Anatomic axis femur (AAF) 
    • a line that bisects the medullary canal of the femur
    • determines entry point of femoral medullary guide rod
    • intramedullary femoral guide goes down anatomic axis of the femur
  • Mechanical axis femur 
    • defined by line connecting center of femoral head to point where anatomic axis meets intercondylar notch
    • obtaining a neutral mechanical axis allows even load sharing between the medial and lateral condyles of a knee prosthesis
  • Valgus cut angle (~5-7° from AAF )
    • difference between AAF and MAF
    • perpendicular to mechanical axis
    • jig measures 6 degrees from femoral guide (anatomic axis)
    • will vary if people are very tall (VCA < 5°) or very short (VCA > 7°)
    • can measure on a standing full length AP x-ray
Tibial alignment
  • Anatomic axis of tibia (AAT) 
    • a line that bisects medullary canal
    • tibia medullary guide (internal or external) runs parallel to it
    • determines entry point for tibial medullary guide rod
  • Mechanical axis of tibia  
    • line from center of proximal tibia to center of ankle
    • proximal tibia is cut perpendicular to mechanical axis of tibia
    • usually mechanical axis and anatomic axis of tibia are coincident and therefore you can usually can cut the proximal tibia perpendicular to anatomic axis (an axis determined by an intramedullary jig)
    • if there is a tibia deformity and the mechanical and anatomic axis are not the same, then the proximal tibia must be cut perpendicular to the mechanical axis (therefore an extramedullary tibial guide must be used)
Patellofemoral Alignment
  • Q angle
    • Abnormal patellar tracking, although not the most serious, is the most common complication of TKA.
    • The most important variable in proper patellar tracking is preservation of a normal Q angle (11 +/- 7°)
      • the Q angle is defined as angle between axis of extensor mechanism (ASIS to center of patella) and axis of patellar tendon(center of patella to tibial tuberosity)
    • Any increase in the Q angle will lead to increased lateral subluxation forces on the patella relative to the trochlear groove, which can lead to pain and mechanical symptoms, accelerated wear, and even dislocation.
      • It is critical to avoid techniques that lead to an increased Q angle. Common errors include:
        • internal rotation of the femoral prosthesis
        • medialization of the femoral component
        • internal rotation of the tibial prosthesis
        • placing the patellar prosthesis lateral on the patella
    • Q angle management in TKA 
Joint Line Preservation
  • Goal is to restore the joint line by inserting a prosthesis that is the same thickness as the bone and cartilage that was removed
    • this preserves appropriate ligament tension
    • if there are bone defects they must be addressed so the joint line is not jeopardized
    • elevating the joint line (> 8mm leads to motion problems) and can lead to
      • mid-flexion instability
      • patellofemoral tracking problems
      • an "equivalent" to patella baja
      • never elevate joint line in a valgus knee until after balancing to obtain full extension
    • lowering joint line can lead to
      • lack of full extension
      • flexion instability

 

Please Rate Educational Value!
4.0
Average 4.0 of 39 Ratings

Qbank (2 Questions)

TAG
(OBQ07.209) Which of the following describes the mechanical axis of a normally aligned limb? Topic Review Topic

1. A vertical line drawn from the femoral head through the center of the knee down to the center of the ankle
2. A valgus angle of 5-7 degrees created by two lines drawn down the shaft of the femur and tibia
3. A varus angle of 3 degrees created by two lines drawn down the shaft of the femur and tibia
4. A vertical line drawn from the femoral head passing 1.5 centimeters lateral to the center of the knee down to the center of the ankle
5. A vertical line drawn from the femoral head passing 1.5 centimeters medial to the center of the knee down to the center of the ankle

PREFERRED RESPONSE ▶
TAG
(OBQ05.136) A 67 year-old woman sustained an ACL tear while playing basketball when she was 35 years-old. She has noted progressive leg deformity and episodes of giving way, and now has pain preventing activity. Non-operative management has failed to provide relief. Treatment should consist of? Topic Review Topic
FIGURES: A          

1. Opening wedge high tibial osteotomy with autograft
2. Closing wedge proximal tibial osteotomy
3. Medial interpositional arthroplasty
4. Medial unicompartmental knee arthroplasty
5. Total knee arthroplasty

PREFERRED RESPONSE ▶




Evidence



Topic Comments